Press the "Save" button to store this number to the programmable button. Repeat Steps to program each of the numbers you want to save into the phone. When you've finished with all the numbers, press the "Speaker" button to save your changes and exit the programming menu.
To dial a programmed number, select an open line on your phone and then press the programmed button. Chris Waller began writing in If you hear the caller's voice on your speaker, speak toward the phone or lift the handset. If your phone rings in 2 short bursts, press the intercom button to talk or lift the handset.
Calls Ringing on Any Monitored Station - If your phone offers the ability to monitor the status of other stations, a BLF light will flash when a call is ringing on another station. You can answer a call ringing at any extension by pressing the DSS button. If you later transfer the call, the BLF light goes out.
You can retrieve the call by pressing the TAP button. Calls Ringing at Another Station in your Group - Your installer my configure the system so that stations are arranged in user groups. If this is the case with your system, you can answer calls ringing at any station in your group.
To answer:. If you are on a speakerphone call, you will hear a ring burst and can go off-hook to receive the call. The call will be disconnected. Using Caller I. Manual Dialing - Press a line button to select a line if your telephone has prime line or idle preference feature enabled, skip this step. Dial the number when you hear the dial tone.
There is usually no need to select a line button as line selection is usually stored as part of the speed dial number. To choose the number stored as a second choice on that button, press Shift and then the button. If you manually choose a line for dialing, press the hold button before pressing the speed dial button.
If you use speed dial dialing after placing a call on hold, pause for a few seconds before you press the speed dial button. Otherwise, the system will choose the line that you have on hold. Redial - To redial the last dialed number, press speaker or hang up to disconnect the call, press " ".
If you hear a busy tone again, press "speaker" to disconnect, otherwise, the phone will ring and you can answer the call by picking up the handset.
To redial once a minute for 10 minutes, press the ARDL button. The intercom light will flash. The Intercom light flashes and you will hear either a ringing or busy tone over the monitor speaker. Pick up the handset within 30 seconds to connect. To cancel the automatic redial, lift and replace the handset or use the phone for another function.
If call cost is not enabled, press the timer button will show up as timer and will display the running duration of the current call. To display the call time for the last call, press HOLD while the phone is idle. To show the cost, press HOLD twice. Intercom Calls - Manually call a station by pressing the intercom button and dialing the extension number. Automatically call by pressing the DSS button. These methods will cause that extension to ring.
To voice call - Manually call a station by pressing the intercom button, dialing the extension number and speaking your announcement. Automatically call by pressing the DSS button and speak your announcement. Using Automatic Callback - For intercom calls only.
If the station you ring is either busy or ringing with no answer, you can prompt the system to ring your phone when the extension you called becomes idle when it was busy or when there is any activity on the extension for no answer calls. This can also be used to prompt a user whose line is in do not disturb to call you back when they are no longer in do not disturb. To use, make the intercom call and press CAMP. Your phone will disconnect from the attempted call.
When the phone you rang is available, your phone will ring with five ring bursts. Press intercom to ring the other phone. Overriding a call - If the extension you call is busy or in do not disturb mode, you can break through using the executive override function provided the feature has been enabled on your system.
When you get a do not disturb signal, press OVER to disable the mode on the called station and either speak your announcement if your phone is in voice-first mode or wait for an answer if your phone is in tone-first mode. If you get a busy tone, the called phone is in speakerphone and cannot be interrupted or that the called party has blocked SOHVA. Note: When a call has been on hold for a specified period of time, you will hear 3 short ring busts on your phone and the flash rate of the line button will increase.
If the call was on exclusive hold, it will be transferred to regular hold at the end of that specified time. Answer a Call Placed on Hold - Press the flashing line button. If you do not see a flashing line button, press TAP. If you do not see the flashing line button, press TAP. Dial the Orbit location destination Now is a great time to replace these antiquated systems with a new hotel phone system.
Prices for some hospitality phone systems are the best they have ever been. Many of these older systems still operate in many businesses and proved to have been a durable phone system. However, they are quite antiquated with older technology so many companies are now replacing them.
Conference Room Phones. Security Camera. Comdial Executec Phones. Comdial Digitech Phones.
0コメント